01
Sample Setup: Secure sample on turntable aligned with test antenna.
Defining safety and reliability through data-driven validation.
Our lab conducts comprehensive lifespan and photometric testing to validate product longevity and optical performance.
Lighting products is conducted under controlled laboratory conditions at rated voltage and ambient temperature to monitor its lifespan.
Static Positioning Test
Precisely locates the light intensity center of the luminaire using laser alignment in a darkroom.
Dynamic Rotation Test
Rotates the luminaire 360 degrees while collecting real-time intensity data to generate distribution curves.
LED luminaires are powered and tested at the center of an integrating sphere, with key photometric, colorimetric and electrical parameters measured after stabilization.
Connector Durability
Charging ports subjected to water immersion, gun heads run over by vehicle wheels, and individual plug drop tests from about 3m height.
Package Drop Test
Simulates transportation hazards. Filled product boxes are dropped from heights (0.5m–1.5m) onto edges, corners, and surfaces. Post-test inspections check for structural damage and functional integrity.
Rollover Test
Products placed on concrete are run over by a standard tire (P225/75R15) at 5000N ± 250N pressure and 8 km/h ± 2 km/h speed. Products must remain safe and functional.
Dust Resistance
Evaluates sealing performance using controlled dust concentrations (2–20 kg/m³) and airflow (1–10 m/s). Complies with IP5X (limited dust ingress) and IP6X (total dustproof) standards.
Rain Test
Spray and immersion tests per GB/T 4208, validating water resistance levels such as IPX3 (spray at 60°), IPX4 (splash-proof), and IPX5/6 (water jet).
Climatic Testing
Covers temperature extremes (-40°C to 200°C), damp heat (e.g., 85°C/85% RH), and salt spray corrosion (5% NaCl solution).
The flexing test is a method to evaluate the fatigue resistance of materials or components under repeated dynamic loads such as bending and stretching. It is widely applied in fields like wires and cables, rubber products, coated fabrics, and more.
Testing of conducted disturbance and radiated disturbance of electronic and electrical products
01
Sample Setup: Secure sample on turntable aligned with test antenna.
02
Configure Parameters: Set test parameters (frequency range, bandwidth, etc.) and switch antenna polarization (horizontal/vertical).
03
Isolate Environment: Close shielded door (9-layer structure), confirm indicator illumination.
04
Monitor Process: Engineer observes sample and antenna status via monitor, records disturbance power waveforms in real-time (English UI).
05
Complete Test: Collect conducted/radiated emission data and generate report.
01
Sample Setup: Secure sample on turntable aligned with test antenna.
02
Configure Parameters: Set test parameters (frequency range, bandwidth, etc.) and switch antenna polarization (horizontal/vertical).
03
Isolate Environment: Close shielded door (9-layer structure), confirm indicator illumination.
04
Monitor Process: Engineer observes sample and antenna status via monitor, records disturbance power waveforms in real-time (English UI).
05
Complete Test: Collect conducted/radiated emission data and generate report.
A standardized needle flame generator (0.5 mm nozzle, ≥35 mm length) fueled by high-purity butane (≥95%) is applied to the sample for a specified duration. During and after ignition, observers record ignition behavior, flame spread, dripping, and whether droplets ignite the underlying tissue. The test evaluates fire resistance under fault conditions.
The three-in-one test system integrates an oscilloscope to capture waveforms in real time, enabling precise analysis of charging pile safety compliance and ensuring electrical safety and protocol conformity.
Dual-gun charging, control guidance, over/under-voltage, residual current, and voltage surge tests
Performs full-power load testing (e.g., 7KW charger at 220V AC/32A) to evaluate stability under prolonged maximum load conditions.
Simulates repeated plugging/unplugging cycles via automated aging programs controlled through computer software.
Global certification for all GONEO products
We test for the only results that matter